Flashing
New flashing at every wall, chimney and vent pipe so the weak points match the new roof.
A roofer in Cresskill can install a new roof in the proper sequence: drip edge, ice and water shield, underlayment, starter strip, flashing, vents and then the roofing itself, and most of what makes a roof last happens before the first shingle goes down. Dial (551) 395-0321 to talk with a local roofer about installation.
When a fairly new roof leaks, the cause is usually how it was installed rather than what it was made of. Nails driven above the reinforced strip, flashing left out at a sidewall and short valleys are the kind of mistakes that show up within a few seasons. None of these are visible from the ground once the job is done.
Choosing the material comes first. Most homes get dimensional asphalt shingles, but metal panels, stone coated steel, tile and slate are all options, and each has its own installation rules. The slope of the roof limits the options, because shingles need a minimum pitch and nearly flat sections need a membrane roof.
Have some basics ready when you call. Say whether the job is a tear-off, an addition or new construction, and whether you have a material or color picked out.
Depending on what the roofer finds, roof installation in Cresskill, NJ can go hand in hand with roof replacement and shingle roof installation.
Need roof installation in Cresskill? Call (551) 395-0321 to reach a nearby roofing contractor.
Call nowHere is the usual order for installing a shingle roof.
Installation starts on a sound, dry deck, so damaged sheathing is cut out and replaced first. On an overlay, the old shingles must lie flat, and any badly curled ones are cut back or replaced.
Metal drip edge is installed at the eaves first, then self-adhering ice barrier covers the eaves and valleys. That layering lets water drain off the metal instead of behind it.
The remaining deck is covered with underlayment, overlapped at the seams and fastened on the maker's pattern. It is the backup layer if a shingle is ever lifted or broken.
Step flashing is woven in with each course along sidewalls, counter flashing covers it at masonry, kickout flashing sits at the bottom of each wall line and new pipe boots go over every vent. Sealant is a backup, not the flashing itself.
A starter strip goes along the eaves and rakes, then shingles are laid in straight courses and nailed in the reinforced nail zone, with four or six nails each as the maker specifies. Correct nailing is what lets the roof stand up to wind.
A ridge vent is cut in along the peak and covered with ridge cap shingles, matched to the intake at the soffits. Balanced intake and exhaust keep the attic drier in winter and cooler in summer.
New flashing at every wall, chimney and vent pipe so the weak points match the new roof.
Starter strip, field shingles and ridge caps, or the panels and trim for a metal roof with fasteners placed where they belong.
A full layer of underlayment plus ice barrier where water collects guards the deck if ice dams form.
Drip edge at the eaves and rakes finishes the edges cleanly.
Ridge vents or other exhaust paired with soffit intake for a drier attic all year.
New roof installation covers three common jobs: replacing a roof after tear-off, roofing a new home and roofing an addition. On an addition, the tricky part is the tie-in, where new valleys and flashing meet older roofing that may not match. Ask whether the new section will match the existing roofing or whether the whole roof should be redone.
The installation should follow the roofing maker's printed instructions, which spell out nailing, underlayment, slope limits and ventilation. A Cresskill roofer should be able to explain how many nails per shingle will be used, what underlayment goes down and what ventilation the attic will have. Vague answers about the hidden layers are worth noticing.
An overlay skips the tear-off and lays new shingles over the current roof. It is only allowed on a roof with one existing layer that lies flat over a solid deck. It means less mess and a faster install.
The trade-offs are real. Nobody can see or repair the decking, the old flashing tends to stay in place, the extra weight sits on the framing, and bumps in the old roof can telegraph through the new shingles. When an overlay is proposed, ask how they confirmed there is only one layer and how the flashing will be handled.
Around Cresskill, roof installation work covers older houses getting their second or third roof and newer homes adding on. Older homes in Cresskill and nearby towns like Demarest, Tenafly, Dumont and Closter often need extra deck work and better ventilation, while newer homes are more likely to need flashing tied into new siding, and a careful installation is what lets a new roof ride out years of weather.
Need roof installation around Cresskill? Call (551) 395-0321 for a Cresskill roofer who serves the towns around it too.
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, building ice dams that push water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Cresskill is busiest after a hard winter and before the next one.
Small roof problems caught early usually stay small repairs.
Roofers in Cresskill know the roof types and weather wear common in local homes.
Ask the roofer about the cause, the options and the estimate before work starts.
More questions? Call (551) 395-0321
A complete new roof from the deck up when repairs no longer make sense, with the old layers removed and the deck checked.
Learn moreChoosing the right shingle and installing every layer under it, from drip edge to ridge cap, for new homes, additions and reroofs.
Learn moreMetal roof installation built around the right panel, finish and trim for the house, with high-temperature underlayment and proper flashing.
Learn moreNew construction roofs coordinated with the builder's schedule, planned with ventilation and penetrations in mind.
Learn moreLooking for something else?
See all roofing servicesCall now for Cresskill roof installation and help in the towns around it.